Re: Drivers for Proxmox
There's no official driver for proxmox other than what's inbox as far as I know. For Debian, the latest OFED driver is up until 7.6
View ArticleRe: Make file for linux kernel
Looking over the release notes, i don't see a support for SLES12 SP3. the latest release of Mellanox (2.4.XX) supports SLES12 default. Could it be that you are looking for SLES11 SP3? (the kernel...
View ArticleClik here to view.
Re: Remove infiniband related drivers?
Mellanox Products: Mellanox OpenFabrics Enterprise Distribution for Linux (MLNX_OFED)
View ArticleUnsuccessful Installing MLNX_OFED_LINUX on RHEL5
I have a redhat server with OS version 5.11 and I'm unsuccessful in installing MLNX_OFED_LINUX-1.5.3-4.0.42-rhel5.10-x86_64. It fails because it does not support the OS version and when I try to build...
View ArticleClik here to view.
IS5022 Switch Fabric
Hello, I'm very new to infiniband, and looking to reuse some gear that already exists in my organization. I have 6 servers with dual single port infiniband cards (MHQH19B-XTR), and currently have 1...
View ArticleHyper-v Cluster 2012 R2 With Mellanox ConnectX-2
Hi, We have two nodes in a windows server 2012 R2 Hyper-v Cluster with 1 dual port ConnectX-2 card for IPoIB/iSCSI SAN access.We also have a stand alone hyper-v for replica with the same card. Actually...
View ArticleRe: Hyper-v Cluster 2012 R2 With Mellanox ConnectX-2
WINOF 4.80 is the last version to support ConnectX-2. Please contact Mellanox Support for assistance with any instability.
View ArticleRe: Need help getting full rate from dual 40GbE network cards on linux systems
MarvinThe maximum bandwidth that you can get from a PCI Gen 3x8 slot is around 52~53 Gbps. Even though the theoretical bandwidth 64Gbps, there is some overhead on the bit encoding, CRC etc. When using...
View ArticleClik here to view.
ConnectX-2 QDR vs ConnectX-3 QDR
I'm looking at expanding my current 15 node cluster to add another 15 nodes. It currently uses the single port ConnectX-2 MHQH19B-XTR listed as QDR 40Gb/s supporting PCIE 2.0. The more recent single...
View ArticleRe: Query on mellanox ml2 mechanism driver
Nurit,Since SriovNicAgent can only VF enable/disable, it won't be able to do any other VF config right ? (eg: MTU or RSS)ThxHarish
View ArticleClik here to view.
Re: Query on mellanox ml2 mechanism driver
no, it won't. however we are working on developing some QoS capabilities in the near future.
View Articlesmall infiniband Windows 7 network - n00b needs some information
Dear fellow infiniband users, I will try and cut my long infiniband story short, so here it goes: Within our small company we are working on separate workstations. We're in the film business so quite...
View ArticleRe: Problem adding kernel support on XenServer
Thank you for all the replies! Just want to give a heads up that the latest MLNX_OFED gets rebuilt without any problems. The versions are:MLNX_OFED_LINUX-2.4-1.0.0Linux XenServer-6.2...
View ArticleClik here to view.
Unassgined class with VF for Ethernet HCA
So I'm doing some experiments with SRIOV on XenServer host and I faced some peculiarities which I don't quite understand.A few words about the setup. I have two HCA installed: one is a dual-port FDR...
View ArticleClik here to view.
Re: ESXi 5.5 & IB Dual Port Card card showing just a sinlge vmnic
I think your configuration under inbox driver.You must remove inbox vSphere inbox driver then install Mellanox En driver 1.9.10.You can see 2 of connector is in online. Below is example scripts. esxcli...
View ArticleRe: Remove infiniband related drivers?
Your answer would make sense if i was asking about OFED, which I am obviously not. I have found the 2.3 drivers and they appear to be working, but I am betting there is a 2.4 version of just the mlx-en...
View Article56Gb/s without a switch ?
I'm using 2 Mellanox MCX354A-FCBT VPI adapters in 2 PCs. These are connected directly without a switch for a "point to point" connection.The speed is 40Gb/s, configured as ETH. QUESTION: is it possible...
View ArticleRe: Cable Options (MCX354A-FCBT-LOW P)
I have the same cards in 2 PCs, work well at 40Gb/s. AfaIk, you will need a FDR capable switch to enable 56Gb/s, SX6036Fwill do it.I bought a couple of Mellanox MC2207310 cables cheap on ebay. I also...
View ArticleRe: Remove infiniband related drivers?
Mellanox Products: ConnectX® EN 10 and 40 Gigabit Linux Driver Ubuntu is there as well.
View Article