Mellanox Switch SNMP Polling for Transfer Rates
I am setting up an ELK stack (Elasticsearch, Logstash, Kibana) on my Ubuntu 14.04.3 LTS server for monitoring, including SNMPv3 & V2c. This server will monitor roughly 200 6036 switches. I am able...
View ArticleClik here to view.
Centos 6.7 + MT25208 InfiniHost III Ex
Hi Guys, I would really appreciate some help installing MT25208 InfiniHost III Ex driver on Centos 6.7. My configuration:# lspci | grep fini06:00.0 InfiniBand: Mellanox Technologies MT25208 InfiniHost...
View ArticleClik here to view.
10/40GbE Architecture Efficiency Maxed-Out? It’s Time to Deploy 25/50/100GbE
All roads lead to 25Gb! Check out mottibeck (Motti Beck):In 2014, after the IEEE rejected the idea of standardizing 25GbE and 50GbE over one lane and two lanes respectively. It was then that a group of...
View ArticleUD Pingpong and MTU on RoCE
With the MTU set for the ethernet device to be 9000 (jumbo frames), I can only send 4012 bytes using ibv_ud_pingpong. Is there a reason why its 4012?I understand there are ethernet headers to be added...
View ArticleClik here to view.
Does SX6012 support enhanced transmission selection and Priority flow based...
Does SX6012 + GW support enhanced transmission selection and Priority flow based control (802.1Qaz, 802.1p/Q and 802.1Qbb)?
View ArticleClik here to view.
Re: boot problem SX6512
I'm not sure why but that did the trick. Thanks! Good thing this wasn't deployed and I had physical access to the box!!
View ArticleEthernet Fabric
Hi dear,I'm looking for Mellanox Ethernet Fabric solution something link what others presented.I mean solutions like Cisco fabricpath, Brocade VCS, Juniper QFabric, and ,.....is there something similar...
View ArticleEthernet Fabric
Hi all,I want to know does Mellanox Ethernet Switches support Trill, SPB or something like these protocols for Ehternet Fabric ?does sx1410 Support vxlan ? what about sx1710 ?can I pass layer 2 vlan...
View ArticleRe: Ethernet Fabric
Hi, We have something called VMS. Please see http://www.mellanox.com/blog/tag/vms/ We also have our new Spectrum switches that supports VXLAN in hardware....
View ArticleRe: Ethernet Fabric
Hi, we don't support Trill or SPB.What do you mean by support of VXLAN? do you mean VXLAN termination? VTEP?QinQ is supported on Mellanox switches. Which adapters do you have?Ophir.
View ArticleClik here to view.
Re: Ethernet Fabric
Hi ophir,To extent Vlans over Layer3 Network ( I want to mention in spine/leaf Topology for Big Datacenters,) there are two approach, one deploying Trill/SPB and the other is vxlan ( Bridging ), the...
View ArticleClik here to view.
Interface goes down during PXE Deployment
Hello * we're going to deploy some new Storage Servers via a 40g NIC by PXE / Netboot and running into trouble. As we've debugged in the last days by TCPDUMP and on our Switch after the TFTP Fetch of...
View ArticleRe: Ethernet Fabric
HI Reza,Currently we don't have VXLAN termination on the switch. This is on the roadmap. It is planned to be introduced with Mellanox switches (Spectrum) with Cumulus OS in few months.Can you add the...
View ArticleRe: MLNX_OFED Update for kernel 3.19 in Ubuntu 14.04.3
Hi,Since the kernel is updating in Ubuntu release, it may be that you can install MLNX_OFED on 14.04.2 but not on 3.Did you try installing version 3.2-2?
View ArticleRe: Ethernet Fabric
Hi Maor, thanks for your support,ok I got it. but for network Diagram I 've sent what mellanox soulution is?I want to carry layer2 over layer3 network specially in big data centers.I did to describe...
View ArticleRe: Ethernet Fabric
Reza, where are you based at? I can have local solution engineer pick up the conversation and assist you in design and implementation. Thanks,Lior
View ArticleMCX354A-FCBT & Switch Speed Issue
I have a MCX354A-FCBT adapter, MC2207128-003 passive cable and SX6015 unmanaged switch.When connecting the cable to the adapter in loopback (i.e. between port A & B) the ibstat command reports a...
View ArticleClik here to view.
Re: Interface goes down during PXE Deployment
While it may not help you specifically with getting pixiecore up and running, the CX3Pro ships with iPXE as a boot rom -- it supports directly downloading the boot config, kernel and initrd over http....
View Article